500PSM02 ABB 1MRB150015R1 Power Supply Module 60W

Description:

The ABB 500PSM02 is a power supply module designed to power a wide range of ABB equipment including drives, controllers and robots. It is a 60W power supply with a wide input voltage range of 88-264 VAC.

Supply modules 500PSM02 and 500PSM03 

The auxiliary supply unit is a DC/DC converter with an output power of 60 W (500PSM02) or 100W (500PSM03). Input voltages in the range 36 V DC to 312 V DC are permissible without any switching of ranges. A second supply unit can be inserted on the right of the rack with 500CRB01 backplane, to achieve redundancy or to supply a higher load. Power dissipation higher than 60W require forced cooling by fan.

Processor module 500CPU03
The application programs are installed in the processor units. The processor module also serves as controller for the internal VME bus. It is equipped with a powerful processor and has two sockets (C and D) for ”industry pack” modules. Such modules are:
• 500LBI02 (pos. C): Data exchange with the station bus LON
• 500PBI01 (pos. D): Data exchange with the process bus MVB

Process bus controller module 500MBA02
The process bus controller module has its own processor and controls the exchange of data via MVB.

Star coupler module 500SCM01
The star coupler module converts the electrical bus signals to optical signals. It has a set of 5 optical transmitter/receiver pairs for connection to other modules (e.g. an additional REC 580 rack or distributed I/O modules). Different electrical process bus signals can be assigned to the 5 optical star coupler interfaces.

Input transformer module 500MTM02
The input transformer module can at ordering be populated with protection grade current transformers (ct), metering grade current transformers (mct), and potential transformers (pt).

The configuration must be stated when ordering (see technical data “Table 18: Selection table of transformer types for ordering 500MTM02” and the ordering section):

Number and types of the protection c.t's, the metering c.t's and the p.t's.

Moreover the rated voltages and the rated currents must be stated. Rated values to be selected:
• rated voltage 63 V, 110 V, 220 V
• rated current 1 A, 5 A
Other rated values can be covered with the transformers stated above by adapting the configuration (e.g. 100 V, 2 A).

Insulating transducer module 500ITM02
The isolating amplifier module allows the registering of small signals. The unit contains 3, 8 resp. 16 input channels. The following small signals can be connected:

±5 mA, ±20 mA, ±10 V.

Analog input units 500AIM02
This module is used to convert the analog signals from the outputs of the input transformer or insulating transducer modules into digital signals for processing.

The analog input module is combined with the 500MTM02 and the 500ITM02 (see technical data).

If both the 500ITM02 and the 500MTM02 modules are placed beside an 500AIM02, care must be taken not to source one and the same channel by both modules.

Binary Input module 500BIM01
The binary input module 500BIM01 has 24 binary opto-coupler inputs (grouped in pairs).

Binary Output module 500BOM01
The binary output module 500BOM01 has 22 contact outputs, six of which are equipped with a 1 mA trip coil supervision.

Forced cooling fan module 500LFE01
The forced cooling fan module 500LFE01 is provided with 4 cooling fans. Each fan speed is supervised and an alarm is given on low fan speed.

The forced cooling fan module adapts the cooling air volume to the ambient temperature with full air volume at 55°C. The 500LFE01 is 44 mm high and shall be mounted directly under REC 580*3.0. The 500LFE01 can be supplied with 90-250 V DC