IS420UCPAH2A GE Mark VIe, Integral I/O Controller Module

Description:

IS420UCPAH2A-C is an Integral I/O Controller Module, manufactured by GE under Mark VIe.
The UCPA is a Mark VIe controller platform that runs application code (control logic).
The controller has both integral I/O capabilities and can communicate with external I/O packs through a simplex IONet. The UCPA Mark VIe controller is commercial in design and not intended for use at any time in a residential environment. The UCPA controller is panel-mounted and includes the following features:
• Controller and I/O in a single module
− Smaller panel footprint with integral I/O
− IONet port for simplex I/O module expansion
• Single 12 V dc power supply, runs at 4 W (low power)
• Can operate in -40 to 70°C ambient temperate range
• No battery or fan
• Cost-effective platform for simplex control and I/O
• Uses ControlST* V05.04 or later with the same ToolboxST* configuration tools across the Mark Controls platform

The Mark VIe UCPA controller contains the following components:
• IS400BPPCH2A processor board
• IS400STWCH1A base I/O board
• IS400WEXPH1A expansion I/O board (included with UCPAH2A)

The IS420UCPAH1A includes the IS400STWCH1A (base I/O board) and the BPPCH2A processor board. It provides the following inputs and outputs:
• Two Hall Effect Pulse Inputs
• Two Analog Inputs (AI)
• Four Digital Inputs or Outputs with feedback (DIO)
The IS420UCPAH2A also includes the IS400WEXPH1A expansion I/O board. The WEXP provides the following additional I/O:
• Six AIs (for a total of 8)
• Two Analog Outputs
• Four DIOs (for a total of 8)

The WEXP-abbreviated Board in this IS420UCPAH2A device's special modular Mark VIeS or VIe Series assembly provides a series of unique I/Os to this IS420UCPAH2A product, including various analog inputs, analog outputs, as well as four total DIOs, as delegated in the IS420UCPAH2A instructional manuals and datasheet attached in our manuals section below for your convenience. The IS420UCPAH2A controller has several LEDs, DIO1-8, Pulse 1 and 2, and an attention LED. The DIO and Pulse LEDs will be solid yellow but the attention LED will be red and green with multiple flash codes. There are both green and red ATTN LED flash codes, some of which are as follows, a red four hertz LED at fifty percent indicating that the diagnostic alarm is active, a red one hertz LED at fifty percent which indicates that no firmware is available, and a green one/two hertz LED at fifty percent indicating that the component has completed power up. All information needed to properly operate the IS420UCPAH2A controller is located in the GEI-10071 Mark VIe Controller UCPA Instruction Guide. 

Frequently Asked Questions:
1.What are IS420UCPAH2A related products?
IS420UCPAH2A, IS420UCPAH2A, IS400BPPCH2A, IS400STWCH1A, IS400WEXPH1A

2.What's IS420UCPAH2A processor, and how much storage does he have?
Processor: Freescale 3308 processor, 332 MHz, (BPPC-based)
Memory: 64 MB/ RAM 256 MB onboard flash/ 32 KB NOVRAM

3.What's IS420UCPAH2A input and output specifications?
Analog Inputs:
Two analog inputs on STWC
Gains used in scaling: 1, 64, 128
Voltage In: Refer to the section, Analog Input Modes.
Current (option channel 2): 4 to 20 mA
Accuracy: 0.1% of full range
Six analog inputs on WEXP
Voltage In: 0 V to 5 V, fixed gain 1 (option channels 6, 7, and 8)
Current: 4 to 20 mA (all channels 3–8)
Accuracy : 0.1% of full range
Analog outputs:
Two analog outputs on WEXP
Voltage : 0 to 10 V
Current : 0 to 20 mA
Accuracy: 0.3% of full range

Datasheet Link:

IS420UCPAH2A GE Mark VIe, Integral I/O Controller Module PDF Datasheet